Solicit opinions on 7 recommended national standards including "Polyethylene Blow Molded Contai

Recently, the State Market Supervision and Administration Bureau issued a request for "Starch Viscosity Determination", "Liquor Inspection Rules and Signs, Packaging, Transportation, Storage", "Ganoderma Lucidum Spore Powder Harvesting and Processing Technical Specifications", "Food Notification of opinions on 7 recommended national standards (draft for approval), "General Technical Specifications for Production Quality Control and Management", " Polyethylene Blow Molded Containers for Food Packaging ", "Tea Filter Paper", and "Daily Insulated Containers".
 
　　"Starch Viscosity Determination" (draft for approval) is a replacement for GB/T22427.7-2008. Compared with the original standard, this standard has some technical changes in addition to structural adjustments and editorial changes. For example, the scope of application of the standard has been changed, and the test method for samples in the rotational viscometer method has been changed; in the rotational viscometer method, the sample preparation of "modified starch completely swollen in cold water into paste" and "modified starch swollen into paste in cold water" have been added. "Determination method; increased rapid viscosity analyzer (RVA) method and so on.
 
　　"Starch Viscosity Determination" (draft for approval) describes the determination methods of starch viscosity by rotational viscometer, Brabender viscometer and rapid viscosity analyzer (RVA). This document applies to both native and modified starches. This document specifies the principles, instruments, reagents, experimental procedures and experimental data processing of the rotational viscometer method, the Brabender viscometer method and the rapid viscosity analyzer (RVA) method.
 
　　"Liquor inspection rules and signs, packaging, transportation and storage" replaces GB/T 10346-2006 "Liquor inspection rules and signs, packaging, transportation and storage", which stipulates the inspection rules and signs, packaging, transportation, Storage requirements apply to the inspection, acceptance and inspection of liquor products.
 
　　"Technical Specifications for Harvesting and Processing Ganoderma Lucidum Spore Powder" replaces GB/T 29344-2012 "Technical Specifications for Harvesting and Processing Ganoderma Lucidum Spore Powder". This standard specifies the technical requirements for harvesting and processing of Ganoderma lucidum spore powder, and is applicable to the harvesting and processing of Ganoderma lucidum and Pinus fir ganoderma spore powder. In addition, the standard also stipulates the harvesting conditions, harvesting methods and processing of Ganoderma lucidum spore powder. Among them, in terms of the processing of Ganoderma lucidum spore powder, the standard stipulates that the processing steps of spore powder are drying - sieving, impurity removal - sterilization - drying - wall breaking - crushing, sieving - packaging; Screening and impurity removal workshops should be clean and equipped with dust-catching facilities.
 
　　"General Technical Specifications for Food Production Quality Control and Management" stipulates the general principles and requirements for food production quality control and management, food quality management institutions, personnel and systems, plant environment and plant design, facilities and equipment, raw materials, auxiliary materials, foodPackaging materials , processing, food quality inspection, handling of products that do not meet food quality requirements, food after-sales management, food quality traceability, withdrawal and recall, training and assessment, verification and evaluation, improvement, and document and record management, etc. This standard is applicable to the quality control and management of all kinds of food production.
 
　　"Polyethylene Blow Molded Containers for Food Packaging" stipulates the requirements, test methods, inspection rules, signs, packaging, transportation and storage of polyethylene blow molded containers for food packaging. It is suitable for polyethylene as the main raw material and hollow blow molding Process molding, used for food packaging, blow molding containers with a nominal capacity of 1000L or less.
 
　　"Tea filter paper" replaces GB/T 25436-2010 "Heat-sealable tea filter paper" and GB/T 28121-2011 "Non-heat-sealable tea filter paper". It is understood that the standard is mainly based on GB/T 25436-2010 and integrates the contents of GB/T 28121-2011. The standard text gives the product classification of tea filter paper, specifies the technical requirements, inspection rules and signs, packaging, transportation, storage, and describes the corresponding test methods. It is suitable for automatic packaging of heat-sealed and non-heat-sealed teabags. The design, production, research and development and testing of filter paper, and the filter paper for packaging of Chinese patent medicines shall be carried out in accordance with the guidelines.
 
　　It is understood that the deadline for feedback on the above-mentioned standards is April 28, 2023, and relevant units or individuals need to send back the "Feedback Form" to the State Administration for Market Regulation by mail, fax or email.